17704692435
Establishes an Artificial Intelligence (AI) and Machine Learning (ML) framework for describing a generic AI system using ML technology. The framework describes the system components and their functions in the AI ecosystem. This document is applicable to all types and sizes of organizations, including public and private companies, government entities, and not-for-profit organizations, that are implementing or using AI systems.
电子版：1196元
/ 折扣价：
1017 元
Provides guidance to assist organizations in integrating security into the processes used for managing their applications. ISO/IEC 27034-1:2011 presents an overview of application security. It introduces definitions, concepts, principles and processes involved in application security. ISO/IEC 27034 is applicable to in-house developed applications, applications acquired from third parties, and where the development or the operation of the application is outsourced.
This part of ISO 7487 specifies the quality of recorded signals, the track layout, and a track format to be used on 130 mm (5.25 in) flexible disk cartridges intended for data interchange between data processing systems.
This technical report describes the methods by which users may measure the performance characteristics of a parallel SCSI domain. This report does not provide definitions or specifications of components utilized in configuring the domain. Physical attributes of the domain are defined in the SCSI family of standards. These standards should be consulted before implementing the recommendations outlined in this technical report. The information in this technical report does not supersede any requirements in the referenced standards.
Provides specifications for format and recording for a 1/2 inch, 9-track magnetic tape to be used for information interchange among information processing systems, communication systems, and associated equipment utilizing ANSI X3.4:1977, American National Code for Information Interchange (ASCII). This standard deals solely with recording on magnetic tape and supports and complements ANSI X3.40:1983, Unrecorded Magnetic Tape for Information Interchange, (9-Track 800 CPI, NRZI, 1600 CPI, PE and 6250 CPI, GCR).
This standard assumes that the reader is familiar with the conventional INT 13h interface, the usage of the BIOS Device Parameter Table, and the basic operation of mass storage devices. This standard describes in detail BIOS functions and data structures that are used as an abstraction layer to allow higher-level applications to access mass storage devices in an interface and command-set independent manner. To comply with this standard, higher-level software shall call the INT functions using the data structures described herein, and system firmware shall provide the INT functions and data structures described herein. The storage industry has increased the capacity and functionality of many types of mass storage devices. This increase in capacity and functionality has required the development of a BIOS interface. This standard documents the BIOS interface that is supplied by many BIOS vendors. This standard defines solutions to the following INT 13h BIOS-specific issues: The INT 13h interface has a limit of 528 megabytes (MB); The INT 13h interface allows more than two devices to be attached to a system but has no consistent method for storing the additional configuration parameters; The INT 13h interface does not define CHS-independent methods for addressing devices. The methods defined by the INT 13h interface are not device-geometry independent. A different method of address representation and operation is needed; Methods of data transfer continue to be added to ATA devices. Capabilities such as, DMA modes, multisector data transfers and PIO modes are not reported to the operating system via the INT 13h interface; Systems require more than two storage devices, and with this requirement comes the requirement to assign the order in which the devices are to be accessed. The INT 13 interface does not provide this capability; The INT 13h interface does not make location and configuration information available to operating systems that do not use the BIOS to access mass storage devices; The INT 13h interface does not provide a linkage between the BIOS device assignments on the operating system device letter assignments; The INT 13h interface does not use data structures that apply to both IA-32 and IA-64 compatible architecture systems.
This standard describes a communication interface between a channel and I/O control units that utilize the Single-Byte Command Code Sets (SBCCS) as implemented in a wide range of data processing systems. It employs information formats and signaling protocols that provide a uniform means for communicating with various types of I/O control units, facilitating a high bandwidth, high performance, and long distance information exchange environment. The signaling protocols and information exchanges are defined at a layer (FC-4) to compatibly utilize the link services and other functions provided by the INCITS Fibre Channel Framing and Signaling (FC-FS-4) and the INCITS Fibre Channel Link Services (FC-LS-3) specifications. This FC-4 Upper Level Protocol is referred to as the Fibre Channel-Single-Byte-6 Command Code Sets Mapping Protocol (FC-SB-6).
This part of ISO/IEC 10026: a) provides a general intro. to the concepts & mechanisms defined in ISO/IEC 10026; b) defines a model of disbributed transaction processing; c) defines the requirements to be met by the OSI TP Service; & d) takes into consideration the need to coexist with other Application Service Elements.
Defines a text-based notation for representing instances of the data model defined in ISO/IEC 13250-2. It also defines a mapping from this notation to the data model. The syntax is defined through an Extended Backus Naur Form (EBNF) grammar.
Defines a protocol for the transport of commands and data over High Performance Serial Bus. The transport protocol, Serial Bus Protocol 2 or SBP-2, requires implementations to conform to the requirements of this standard as well as to ISO/IEC 13213:1994 and permits the exchange of commands, data and status between initiators and targets connected to Serial Bus.
对不起，暂未有相关搜索结果！
